Hazard Risk Category Levels
The NFPA® has identified various FR hazardous risk category levels, which are numbered by severity from 1 to 4. Hazard Risk Category is the level of arc flash protection clothing you must wear to protect against a minimum level of incident energy measured in calories per centimeter squared. Meaning, electrical equipment, depending upon the energy delivering capability, under fault conditions can cause an explosion, or arc fault of a certain level, again measured in calories per centimeter squared. That explosion can deliver a certain amount of heat to a certain distance. Each level, 0-4, is rated at a certain amount of flame resistance, again measured in cal/cm2.
The chart, based on specific job tasks, ranges from HRC 1 (which is low risk and allows for 100% treated cotton), up to HRC 4 (which is high risk and requires FR clothing with a minimum arc rating of 40). The HRC is used to determine the necessary arc rating of a garment worn during a given job task.
(Typical number of clothing layers is given in parentheses)
Arc Rating of PPE
FR shirt and FR pants or FR coveralls (1 layer)
Cotton underwear plus FR shirt and FR pants (1 or 2 layers)
Cotton underwear plus FR shirt and FR pants plus FR coveralls, or Cotton underwear plus two FR coveralls (2 or 3 layers)
Cotton underwear plus FR shirt and FR pants plus multilayer flash suit (3 or more layers)
ARC Rating Explained
A value of the energy necessary to pass through any given fabric to cause with 50% probability a second or third degree burn. This value is measured in calories/cm². The necessary Arc Rating for an article of clothing is determined by a Hazard/Risk Assessment and the resulting HRC. Usually measured in terms of ATPV or EBT. Simple put the ARC rating determines the protective characteristics of the fabric. The higher the ARC rating value the greater the protection. When the product is sold to protect workers from arcing faults, clothing manufacturer are required in indicate the ARC rating. For more info visit www.nfpa.org.
Arc Flash An explosive release of energy caused by an electrical arc. An arc flash results from either a phase to ground or a phase to phase fault caused by such occurrences as accidental contact with electrical systems, build up of conductive dust, corrosion, dropped tools, and improper work procedures. During an arc flash, the temperature can reach 35,000° Fahrenheit, and exposure to an arc flash can result in serious burn injury and death. Every year, more than 2,000 people are admitted to burn centers with severe arc-flash burns. For more info visit www.nfpa.org.
NFPA® 2112 Explained
NFPA® 2112 provides minimum performance criteria and sets clear guidelines for minimum design,performance, certification requirements and test methods for Flame Resistant garments for use in areas at risk from flash fires—such as those where flammable gases or vapors, or combustible dusts might be present. The standard calls for flash fire testing to be conducted at three seconds with a pass/fail rate of 50% total body burn under ASTM F1930 (Standard Test Method for Evaluation of Flame Resistant Clothing for Protection Against Flash Fire Simulations Using an Instrumented Manikin) testing protocols. Bulwark garments have been certified by Underwriters Laboratories to meed the requirements of the NFPA® 2112 Standard on Flame Resistant Garments for Protection of Industrial Personnel Against Flash Fire, and Canadian General Standards Board (CGSB) Standard 155.20, Workwear for protection against Hydrocarbon Flash Fire. For more info visit www.nfpa.org.
National Fire Protection Association, known as NFPA, was established in 1896, it's mission is to reduce the worldwide burden of fire and other hazards on the quality of life by providing and advocating consensus codes and standards, research, training, and education. NFPA® is the world's leading advocate of fire prevention and an authoritative source on public safety, NFPA® develops, publishes, and disseminates more than 300 consensus codes and standards intended to minimize the possibility and effects of fire and other risks. For more info visit www.nfpa.org.
NFPA® 2112 Compliant
Bulwark Products marked as NFPA® 2112 Compliant are Certified by Underwriters Laboratories (UL) or other independent third party laboratories to meet the requirements of NFPA® 2112 Standard on Flame Resistant Garments for Protection of Industrial Personnel Against Flash Fire, 2012 Edition.
NFPA & 70E Are Resistered Trademarks of the National Fire Protection Association (NFPA).